| Item |
Single-function models |
Single-function models |
Green LED |
Blue LED |
Infrared LED |
| Model |
E3X-DA@SE-S |
E3X-DA@-S |
E3X-DAG@-S |
E3X-DAB@-S |
E3X-DAH@-S |
| Light source (wavelength) |
Red LED (635 nm) |
Green LED (525 nm) |
Blue LED (470 nm) |
Infrared LED (870nm) |
| Power supply voltage |
12 to 24 VDC ±10%, ripple (p-p) 10% max. |
| Power consumption |
960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC) |
| Control output |
Load power supply voltage: 26.4 VDC; NPN/PNP open collector; load current: 50 mA max.; residual voltage: 1 V max. |
| Remote control input |
No-voltage input (contact/non-contact) |
— |
| Protection circuits |
Reverse polarity for power supply connection, output short-circuit |
| Super-high- speed mode |
— |
Operate: 48 ms, reset: 50 ms *1, *2 |
| High-speed mode |
— |
Operate/reset: 250 ms |
| Standard mode |
Operate or reset: 1 ms |
| High-resolution mode |
— |
Operate or reset: 4 ms |
| Sensitivity setting |
Teaching or manual method |
| Power tuning |
— |
Light emission power and reception gain, digital control method |
| Timer function |
— |
Select from OFF-delay, ON-delay, or one-shot timer.1 ms to 5 s (1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments, 200 ms to 1 s set in 100-ms increments, and 1 to 5 s set in 1 s-increments) |
| Automatic power control (APC) |
High-speed control method for emission current |
| Zero-reset |
— |
Negative values can be displayed. (Threshold value is shifted.) |
| Initial reset |
Settings can be returned to defaults as required. |
| Mutual interfer- ence prevention |
Possible for up to 10 Units *3 |
| Display |
Operation indicator (orange) |
Operation indicator (orange), Power Tuning indicator (orange) |
| Digital display |
incident level + threshold |
Select from incident level + threshold or other 6 patterns |
| Display orientation |
— |
Switching between normal/reversed display is possible. |
| Ambient illumination (Receiver side) |
Incandescent lamp: 10,000 lux max. Sunlight: 20,000 lux max. |
| Ambient temperature range |
Operating: Groups of 1 to 2 Amplifiers: -25°C to 55°C Groups of 3 to 10 Amplifiers: -25°C to 50°C Groups of 11 to 16 Amplifiers: -25°C to 45°CStorage: -30°C to 70°C (with no icing or condensation) |
| Ambient humidity range |
Operating and storage: 35% to 85% (with no condensation) |
| Insulation resistance |
20 MΩ min. (at 500 VDC) |
| Dielectric strength |
1,000 VAC at 50/60 Hz for 1 minute |
| Vibration resistance |
Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions |
| Shock resistance |
Destruction: 500 m/s2, for 3 times each in X, Y and Z directions |
| Degree of protection |
IEC 60529 IP50 (with Protective Cover attached) |
| Connection method |
Pre-wired or amplifier unit connector |
| Weight (packed state) |
Pre-wired model: Approx. 100 g, Amplifier unit connector model: Approx. 55 g |
| Case |
Polybutylene terephthalate (PBT) |
| Cover |
Polycarbonate (PC) |
| Accessories |
Instruction manual |
English
Deutsch
한국어